|
LIM Action (APP/LIM)
View Options:
(help)
| Focus: |
Maintenance / Operation |
| Structures: |
Abstract / Concrete |
Description:
Valid LIM actions that are reported in the LIMSTATE telemetry packet.
Definition:
| 0 |
Unknown Action (LIMACTUNKNOWN) |
|
An unrecognized action occurred. |
| 1 |
LIM Start Action (LIMACTSTART) |
|
The LIM task started. |
| 2 |
Operating Mode Change Action (LIMACTOPMODECH) |
|
The operating mode changed. |
| 3 |
Main Feed On Action (LIMACTMAINFEED) |
|
LIM enabled power to the main feed and initialized the SIU. |
| 4 |
Power On Action (LIMACTPOWERON) |
|
LIM enabled power to one or more components of the LAT. |
| 5 |
Power Off Action (LIMACTPOWEROFF) |
|
LIM disabled power from one or more components of the LAT. |
| 7 |
Event Fabric Insert Action (LIMACTEVENTINS) |
|
LIM added one or more components to the event fabric. |
| 8 |
Event Fabric Remove Action (LIMACTEVENTREM) |
|
LIM removed one or more components from the event fabric. |
| 9 |
Load Shed Start Action (LIMACTSHEDBEGIN) |
|
LIM started disabling instrument power in response to a Load-Shed command. |
| 10 |
Load Shed End Action (LIMACTSHEDEND) |
|
LIM finished disabling instrument power in response to a Load-Shed command. |
| 13 |
LPA Start Action (LIMACTLPASTART) |
|
LIM sent the LPASTART command to the LPA task. |
| 14 |
LPA Set Mode Action (LIMACTLPASSETMOD) |
|
LIM called the LPA_set_mode() function to change the observation mode. |
| 15 |
LPA Stop Action (LIMACTLPASTOP) |
|
LIM sent the LPASTOP command to the LPA task. |
| 16 |
LTC Stop Action (LIMACTLTCSTOP) |
|
LIM sent the LTCSTOP command to the LTC task. |
| 17 |
SIU Reboot Action (LIMACTSIUREBOOT) |
|
LIM is about to reboot the SIU. |
| 19 |
SAA Configure Action (LIMACTSAACFG) |
|
LIM configured the LAT instrument for SAA transit. |
| 21 |
Non-SAA Configure Action (LIMACTNONSAACFG) |
|
LIM configured the LAT instrument for non-SAA operation. |
| 22 |
LCI Calibrate Action (LIMACTCALSTART) |
|
LIM sent the LCICALIBRATE command to the LCI task. |
| 23 |
LCI Abort Action (LIMACTCALABORT) |
|
LIM sent the LCIABORT command to the LCI task. |
| 24 |
LCI Other Command Action (LIMACTCALOTHER) |
|
LIM sent some 'other' command to the LCI task. |
| 25 |
Diagnostic Start Action (LIMACTDIAGSTART) |
|
LIM sent the Diagnostic-Start command to the diagnostic task. |
| 26 |
Diagnostic Abort Action (LIMACTDIAGABORT) |
|
LIM sent the Diagnostic-Abort command to the diagnostic task. |
| 27 |
Diagnostic Other Command Action (LIMACTDIAGOTHER) |
|
LIM sent some 'other' command to the diagnostic task. |
| 30 |
LCI Complete Action (LIMACTCALCOMP) |
|
LIM received the LCICOMPLETE message from the LCI task. |
| 31 |
Diagnostic Complete Action (LIMACTDIAGCOMP) |
|
LIM received the Diagnostic-Complete message from the diagnostic task. |
| 32 |
LPA Complete Action (LIMACTLPACOMP) |
|
LIM received the LPACOMPLETE message from the LPA task. |
| 33 |
LCI Task State Change Action (LIMACTLCISTATE) |
|
LIM changed the state of the LCI task. |
| 34 |
Diagnostic Task State Change Action (LIMACTLDFSTATE) |
|
LIM changed the state of the diagnostic task. |
| 35 |
LPA Task State Change Action (LIMACTLPASTATE) |
|
LIM changed the state of the LPA task. |
| 37 |
ARR Mode State Change Action (LIMACTARRSTATE) |
|
The ARR observation mode state changed. |
| 40 |
TOO Mode State Change Action (LIMACTTOOSTATE) |
|
The TOO observation mode state changed. |
| 42 |
LPA Active Command Action (LIMACTLPAACTIVE) |
|
LIM sent an 'active' command to the LPA task. |
| 43 |
LPA Idle Command Action (LIMACTLPAIDLE) |
|
LIM sent an 'idle' command to the LPA task. |
| 44 |
Virtual Mode Change Action (LIMACTVIRTMODE) |
|
The virtual mode changed. |
| 45 |
SAA State Change Action (LIMACTSAACHANGE) |
|
The SAA transit state changed. |
| 46 |
LPA Restart Action (LIMACTLPARESTART) |
|
LIM called the LPA_resume() function to restart an observation. |
| 47 |
GBM Repoint Recommend Action (LIMACTREPREC) |
|
LIM received a Candidate Repoint Recommendation message from the GBM which recommended a repoint. |
| 48 |
GBM No-Repoint Recommend Action (LIMACTREPNOREC) |
|
LIM received a Candidate Repoint Recommendation message from the GBM which did not recommend a repoint. |
| 49 |
GBM Command Forward Action (LIMACTGBMCMD) |
|
LIM forwarded a command from the GBM to the LPA task. |
| 50 |
Slew Request Action (LIMACTSLEWREQ) |
|
LIM sent a Slew-Request command to the spacecraft. |
| 51 |
Slew Accept Action (LIMACTSLEWACCEPT) |
|
LIM received a Slew-Request-Reply from the spacecraft which indicated that the request was accepted. |
| 52 |
Slew Reject Action (LIMACTSLEWREJECT) |
|
LIM received a Slew-Request-Reply from the spacecraft which indicated that the request was rejected. |
| 53 |
Primary PID Select Action (LIMACTPIDSELPRI) |
|
LIM selected the primary PID input signals. |
| 54 |
Redundant PID Select Action (LIMACTPIDSELRED) |
|
LIM selected the redundant PID input signals. |
| 55 |
LIM Stop Action (LIMACTSTOP) |
|
The LIM task was stopped. |
| 56 |
ACD Bias Configure Action (LIMACTBIASACD) |
|
LIM configured the ACD bias voltages. |
| 57 |
CAL Bias Configure Action (LIMACTBIASCAL) |
|
LIM configured the CAL bias voltages. |
| 58 |
TKR Bias Configure Action (LIMACTBIASTKR) |
|
LIM configured the TKR bias voltages. |
| 59 |
GBM Interface Configure Action (LIMACTGBMSTATE) |
|
The configuration of the GBM interface changed. |
| 60 |
HV Interface Configure Action (LIMACTHVSTATE) |
|
The configuration of the high-voltage interface changed. |
| 61 |
LCI Calibrate Status Action (LIMACTCALSTRTST) |
|
LIM received a status code for an LCICALIBRATE command that it sent to the LCI task. |
| 62 |
Diagnostic Start Status Action (LIMACTDIAGSTRTST) |
|
LIM received a status code for a Diagnostic Start command that it sent to the diagnostic task. |
| 63 |
LPA Start Status Action (LIMACTLPASTARTST) |
|
LIM received a status code for an LPASTART command that it sent to the LPA task. |
| 64 |
LCI Abort Status Action (LIMACTCALABRTST) |
|
LIM received a status code for an LCIABORT command that it sent to the LCI task. |
| 65 |
Diagnostic Abort Status Action (LIMACTDIAGABRTST) |
|
LIM received a status code for a Diagnostic Abort command that it sent to the diagnostic task. |
| 66 |
LPA Stop Status Action (LIMACTLPASTOPST) |
|
LIM received a status code for an LPASTOP command that it sent to the LPA task. |
| 67 |
Primary GBM Interrupt Enable Action (LIMACTENGBMPRI) |
|
LIM enabled the primary GBM trigger interrupt signal. |
| 68 |
Redundant GBM Interrupt Enable Action (LIMACTENGBMRED) |
|
LIM enabled the redundant GBM trigger interrupt signal. |
| 69 |
Primary GBM Interrupt Action (LIMACTGBMINTPRI) |
|
LIM received an interrupt from the primary GBM trigger interrupt signal. |
| 70 |
Redundant GBM Interrupt Action (LIMACTGBMINTRED) |
|
LIM received an interrupt from the redundant GBM trigger interrupt signal. |
| 71 |
Slew Request Pending Status Action (LIMACTREPREQST) |
|
The Slew-Request PENDING status changed. |
| 72 |
GBM Calculate Information Action (LIMACTCALCINFO) |
|
LIM received a Calculated Information message from the GBM. |
| 73 |
GBM Closeout Action (LIMACTCLOSEOUT) |
|
LIM received a Closeout message from the GBM. |
| 74 |
Primary GBM Interrupt Disable Action (LIMACTDISGBMPRI) |
|
LIM disabled the primary GBM trigger interrupt signal. |
| 75 |
Redundant GBM Interrupt Disable Action (LIMACTDISGBMRED) |
|
LIM disabled the redundant GBM trigger interrupt signal. |
| 76 |
GRB Suspected Action (LIMACTGRBSUSPECT) |
|
LIM received a GRB-Suspected message from the LPA task. |
| 77 |
GRB Confirmed Action (LIMACTGRBCONFIRM) |
|
LIM received a GRB-Confirmed message from the LPA task. |
| 78 |
GRB Finished Action (LIMACTGRBFINISH) |
|
LIM received a GRB-Finished message from the LPA task. |
| 79 |
LPA GBM Interrupt Action (LIMACTLPAGBMINT) |
|
LIM called the LPA_gbm_int() function to notify LPA of a GBM interrupt. |
Used by:
|
